DIY - Installing LED Yellow Fog Light Bulbs 2009 Toyota Rav4

This is a DIY on how to replace and upgrade your fog lights on a Toyota Rav4 2009

Real simple all you have to do is turn the wheel the opposite direction that you are gonna install the bulb .

Pull the splash guard toward you there might be a plastic clip you have to remove . Once you have it pull in then you can see and locate the bulb socket .

Always make sure you have the correct bulb .

Once both sides are done then you can test out the bulbs .

More DIY @ www.corollacarclub.proboards.com 

.

DIY - Installing Door Window Vent Visors 2009 Toyota Rav4

This is a DIY on how to install window vent visors on a 2009 Toyota Rav4 

First thing you do is to let the window vent visors lay flat in the sun for at least a hour so that it can be more flexible , Activate the glue cause once you install it and do not put it in the sun the plastic will form and the glue will get reactivated and possibly fall off or shape funny .

You clean the door frame with alcohol to remove and grease or dirt . 

Make sure before you peel the tape that you properly fit the vent visor to make sure it is correct and to know where you will be putting it on . 

Peel strip then press with your finger if you can do it out of the sun , continue pressing area for a few days especially when it is in the sun to make sure the glue sticks real good . 

More DIY @ www.corollacarclub.proboards.com 

.

DIY - Installing LED Reverse Light , Rear Side Marker & Tag Light Bulb 2009 Toyota Rav4

This DIY is how to upgrade you standard bulbs to a LED bulbs for your reverse lights and tag lights on a 2009 Toyota Rav4 

This is real simple with a flat head screwdriver you remove the tag light assembly from the left and pull down replacing your bulb and putting in the LED bulb . 

Now on this one the only bulbs you can replace in this lens is the reverse bulb , turn signal bulb and side marker .

That is because the brake light bulbs are factory LED so if one of those blows out you have to replace the brake light assembly . 

You pop to door open where the jack is located and on the passenger side you will se a door as well to . By slipping your small hand inside you can locate the bulbs and replace them to a upgraded LED bulb . 

More DIY @ www.corollacarclub.proboards.com 

.

DIY - Replacement all Interior bulbs to LED bulbs 2009 Toyota Rav4

 This is a DIY on how to replace all the interior bulbs to a upgraded LED bulbs in a 2009 Toyota Rav4

Center Dome , Visor Mirrors , Reading Dome Light , Rear Door Light 

When replacing the center dome light all you have to do with a flat head screw driver or a plastic removal tool and separate the lens from the part itself leaving the dome part on the roof .

Now the rear door light is a little tricky , Once you remove the part itself -  NOTE : you must pry from the switch side - Once you have the part removed then you can separate the lens from the piece .

Now the map light or reading light the one for the driver and passenger again you pull away from the area I have my plastic tool .

Now the visor mirror on again you have to pull from the left side of the part then replace it with your new LED bulb 

More DIY @ www.corollacarclub.proboards.com 

.

DIY Gauge Cluster LED Upgrade Bulbs 2000 Toyota Camry

This is a DIY Gauge Cluster upgrade or replacement bulbs on a 2000 Toyota Camry 

Remove the two screws then your gonna need a flat head screw driver on each ends then pull towards you 

You will see four screws holding the gauge cluster 

Twist and turn bulb out - Be careful you do not damage anything in the back of the cluster - Choose what ever color you wish to put in - Test before putting the cluster back that the LED are working 

Then there you have it nice and bright 

More DIY at www.corollacarclub.proboards.com 

.