DIY Spark Plug Replacement 2005 Toyota Corolla S

This is a DIY for a 9th gen Corolla 1zz Motor         

       

These plugs DO NOT have to be gapped but it is good to check it out .40

The top photo shows OEM plugs for 1zz or 2zz motor 

Remove the engine top cover 

You will have to remove the rail for the coil packs - then you can remove the coils in order by either marking them or laying them down in order -  You can mix the coils up but why 

Always check your spark plugs to see if they are running correctly - Make sure you purchased the right one either Denso or NGK all others NOT RECOMMENDED  

By using Dielectric ad Anti Seize to ensure for future replacements it can be easier .

for more information - www.COROLLACARCLUB.proboards.com 

.

DIY Replacing Spark Plugs 2000 Infiniti I30

This is a DIY for a Infiniti I30 with a 3.0 Nissan Motor - You DO NOT have to remove the hood but when I did this DIY I was replacing my hood with a new one .

The front plugs are the easiest , All you have to do is remove the single bolt holding the ignition coil - When pulling the coil up use slight twist and pull - Make sure you inspect your coil tips for oil - If you see signs of oil then you need to replace your valve cover and grommets 

I gap my plugs at .44 and use some anti seize - electrical lube - This motor does use double platinum plug

Now the rear plugs are easy to remove - All you have to do is remove the top part of the gas and transmission cable bracket - Again check the coils for oil on the tips - But when you put these plugs back MAKE SURE YOU HAVE PLENTY OF ROOM BECAUSE YOU CAN CRACK THE BACK SIDE PLUGS - when tightening plug do it slow and keep the extension straight -  MAKE SURE WHEN YOU DO THIS IT IS SILENCE AS POSSIBLE SO THAT YOU CAN HEAR IF YOU HAVE CRACKED THE PLUG - IF YOU HEAR ANY WEIRD SOUND WHILE TIGHTENING REMOVE THE PLUG TO MAKE SURE - THERE SHOULD BE NO SOUNDS WHEN TIGHTENING THESE PLUGS - Once you done all of then then you can put the coils back on 

more diy @ www.corollacarclub.proboards.com 

.

DIY - Tercel 91 - 94 Oil Change & Tune Up

 

 

This DIY is on a 1993 Toyota Tercel with a 1.5L FI SOHC 4cyl , 3E - E .

 

 This is a basic oil change , You drain your oil pan , remove the oil filter , Because this vehicle has alot of miles I did a 10w 40 oil change and added STP . Its your car you can put either OEM or what is good for you .

 

 

Make sure you wipe the area before putting back your new oil filter and put a light coat of oil on the rubber part on the oil filter hand tighten then add oil .

 

 

 

This is the Tune up .

Before removing your distributor cap there is the intake hose to your air filter cause it will make it easier . Its your car so if you don't or do either way .

Now on this vehicle the plugs & cap are one piece . I'm sure they sell them separate but I bought them as one . When you put your rotor button back I added some anti seize .

Then once you replaced your cap & rotor you can remove the front of the cold intake hose so you can gave easy access to the spark plugs .

Make sure you put anti seize on the thread of all your plugs , gap your plugs . They say your plugs are pre gap but its your car on whether you trust them or not .

The plastic holder for the wires broke so I added a tie strap so that the wires don't fall on the heat shield of the exhaust , Plus I took off the plastic heat shield for the wire that is the farthest so that the heat doesn't soften of melt the wire .

Once you have your plugs back together then you can change your PCV valve .

 

And last you can replace your air filter .

 

 

Once you are finished you start your car and listen for misfires . If all sounds well then you have completed the most easiest tune up and oil change .

 

 

More information or help you can contact me at www.CorollaCarClub.proboards.com or http://rinconrolla98.blogspot.com